StatRapid Load Testing

StatRapid Load Testing

StatRapid is a method for Rapid Load Testing: A powerful quasi static test method for determining the static load capacity of piles in compliance with ASTM D7383 and EuroCode 22477-10

 

Key benefits

  • Fast method for high strain pile testing
  • Combines advantages of SLT and DLT
  • Eliminates disadvantages of SLT and DLT
  • Direct measuring of force and displacements
  • No stress wave analysis, no signal matching: direct load-settlement diagram
  • Elaboration user independent
  • High accuracy, reliability and reproducible
  • In compliance with international standards (ASTM, EuroCode, etc)

StatRapid is one of the methods of Rapid Load Testing

StatRapid device ready in Down Town Utrecht to perform Rapid Load Testing
StatRapid device ready in Down Town Utrecht to perform Rapid Load Testing

Rapid Load Testing is a method were a pile is loaded in a short moment, giving a gentle push on the pile top. This method is much faster than static load testing. The duration of the load is much longer than during a Dynamic Load Test or PDA. Due to the long duration of the load, no stress waves phenomena are involved. When the requirements of the quasi static situation are fulfilled, the interpretation of the Rapid Load Test results are straightforward, without stress wave analysis and without Signal Matching. As a result, the results of Rapid Load Tests are more accurate, reliable, and man-independent.

Rapid Load Testing has two major test methods: StatNamic and StatRapid.

Want to know more? Contact Joost Bakker at bakker@allnamics.com

StatRapid

StatRapid is the quasi static, high strain test method for determination of the bearing capacity of foundation piles. Within the StatRapid test method a drop weight is dropped on a special designed StatRapid cushioning. Due to its special characteristics, the kinetic energy of the drop weight is transferred in a relative long duration push on top of the pile. StatRapid is based on the Rapid Load Testing method, and therefor combines all benefits from Static and Dynamic Testing: A StatRapid Load Test requires limited time, lower costs and yields high accuracy results.

StatRapid is one of the methods for Rapid Load Testing, here ready to use for the check on the foundation of an onshore wind farm
StatRapid saves time and reduces the influence on the site logistics. A small footprint, and less transport movements

THE STATRAPID TEST DEVICE

The StatRapid device is available with weights of 40 and 80 tonnes and more. Leading to testing load up to 12 and 20 MN and more, depending on the soil and pile conditions.

Each device consists out a basic frame including load cells, the special for Rapid Load Testing designed cushioning, which is modular both in number of spring elements as in stiffness of each spring element. The upper frame includes the hydraulics for lifting and catching and the test weight. The test weight is also modular. Weight can be added or removed in order to optimize the setup for each pile, depending on soil conditions and on the required test load.

 

ALLWAVE-RLT

Relationship between drop height and test load will be determined prior to the tests, using AllWave-RLT. This program, as part of the AllWave Software Package, simulates the Rapid Load Tests, incorporating all possible influences from pile, soil and testing setup.

 

MONITORING SENSORS 

The monitoring system of the StatRapid Load Testing consists of the PDR data acquisition unit and sensors recording the following quantities at the pile top:

  • The load, measured with load cells
  • Displacements with the Allnamics Reyca optical system with reflector on the pile
  • Accelerations

Direct measurements of loads and settlements gives direct measured load-settlement diagrams. By analyzing the results with the Unloading Point Method, according to ASTM and EuroCodes (and other codes), the static load diagram is obtained.

 

SPECIFICATIONS AND CODES

The tests of the Rapid Load Testing are in compliance with a.o. ASTM D7383, and EuroCode EN ISO-22477-10, as well as other national codes (i.e. Dutch CUR-230). According to these codes:

  • Test data analysis based on user-independent principles,
  • no signal matching is required.
  • taking into account loading rate dependencies of the soil (as for DLT and PDA)

ADVANTAGES

  • Test data analysis based on user-independent principles,
  • No signal matching is required.
  • Taking into account loading rate dependencies of the soil (as for DLT and PDA)

Rapid Load Testing in Hamburg, Germany

allnamics-silhouette

Start typing and press Enter to search